Journal of the Korea Concrete Institute (콘크리트학회논문집)

Korea Concrete Institute (한국콘크리트학회)
권호 표지
DOI QR코드

DOI QR Code

Influence of Number of Twist on Tensile Behavior of High Performance Fiber Reinforced Cementitious Composites with Twisted Steel Fibers

비틀림 강섬유의 비틀림 횟수가 고성능 섬유보강 시멘트 복합재료의 인장거동에 미치는 영향

  • Kim, Dong-Joo (Dept. of Civil and Environmental Engineering, Sejong University)
  • 김동주 (세종대학교 토목환경공학과)
  • Received : 2010.03.25
  • Accepted : 2010.05.24
  • Published : 2010.08.31
Download PDF
⟨ Previous Next ⟩

Abstract

This research investigated the influence of the number of twist on single fiber pullout behavior of Twisted steel (T-) fiber and tensile behavior of high performance cementitious composites reinforced with the (T-) fibers (HPFRCC). Micromechanical pullout model for T- fibers has been applied to analytically investigate the influence of various fiber parameters including the number of twist on single fiber pullout behavior; and, to optimize the number of twist to generate larger pullout energy during fiber pullout without fiber breakage. In addition, an experimental program including single fiber pullout and tensile tests has been performed to investigate the influence of twist ratio experimentally. Two types of T- fiber with different twisted ratios, T(L)- fiber (6ribs/30 mm) and T(H)- fiber (18ribs/30 mm), were tested. T(L)- fiber produced higher equivalent bond strength (larger pullout energy) although T(H)- fiber produced higher pullout stress during pullout since T(H)- fiber showed fiber breakage during pullout. Tensile test results confirmed that T(L)- fiber in high strength mortar generates better tensile performance of HPFRCC, e.g., load carrying capacity, strain capacity and multiple micro-cracking behavior.

이 연구는 비틀림 강섬유(T- 섬유) 의 비틀림 횟수가 인발거동과 T- 섬유를 사용한 고성능 섬유보강 시멘트 복합재료의 인장거동에 미치는 영향을 조사하였다. T- 섬유의 여러 인자와 비틀림 횟수가 섬유의 인발거동에 미치는 영향을 해석적으로 조사하고, 최대의 인발에너지를 생성할 수 있는 비틀림 횟수를 조사하였다. 이와 더불어 T- 섬유의 인발시험과 인장시험을 수행하여, 비틀림 횟수가 고인성 섬유보강 시멘트 복합재료의 인장거동에 미치는 영향을 조사하였다. 비틀림 횟수가 6ribs/30 mm인 T(L)- 섬유와 비틀림 횟수가 18ribs/30 mm인 T(H)- 섬유를 사용하였다. T(H)- 섬유는 인발시험시 섬유의 파단되어, T(L)- 섬유보다 높은 인발응력을 유발했음에도 불구하고 낮은 총 인발에너지를 생성하였다. 이러한 인발 시험서의 결과는 인장 거동에도 분명하게 반영되었다. T(L)- 섬유를 사용한 고인성 섬유보강 시멘트 복합재료의 경우, T(H)- 섬유의 사용시보다, 우수한 변형능력과 에너지 흡수능력, 그리고 미세균열 거동을 보였다.

Keywords

References

  1. Naaman, A. E., “Engineered Steel Fibers with Optimal Properties for Reinforcement of Cement Composites,” Journal of Advanced Concrete Technology, Japan Concrete Institute, Vol. 1, No. 3, 2003, pp. 241-252. https://doi.org/10.3151/jact.1.241
  2. Naaman, A. E., “Fibers with Slip-Hardening Bond,” in High Performance Fiber Reinforced Cementitious Composites-HPFRCC 3, H.W. Reinhardt and A.E. Naaman, Editors, RILEM Pro 6, RILEM Publications SARL, Cachen, France, 1999, pp. 371-385.
  3. Kim, D. J., Naaman, A. E., and El-Tawil, S., “Comparative Flexural Behaviour of Four Fiber Reinforced Cementitious Composites,” Cement and Concrete Composites, Vol. 30, No. 10, 2008, pp. 917-928. https://doi.org/10.1016/j.cemconcomp.2008.08.002
  4. Sujivorakul, C. and Naaman, A. E., “Tensile Response of HPFRC Composites Using Twisted Polygonal Steel Fibers,” Proceedings of Fiber Reinforced Concrete: Innovation for Value, ACI convention, Toronto, ACI Special Publication, Vol. 216, 2003, pp. 161-180.
  5. Chandrangsu, K. and Naaman, A. E., “Comparison of Tensile and Bending Response of Three High Performance Fiber Reinforced Cement Composites,” in Print, HPFRCC4, Ann Arbor, USA, 2003, pp. 259-274.
  6. Kim, D. J., El-Tawil, S., and Naaman, A. E., “High Performance Fiber Reinforced Cementitious Composites with Innovative slip hardening Twisted steel fibers,” International Journal of Concrete Structures and Materials, Vol. 3, No. 2, 2009, pp. 119-126. https://doi.org/10.4334/IJCSM.2009.3.2.119
  7. Kim, D. J., El-Tawil, S., and Naaman, A. E., “Loading Rate Effect on Pullout Behaviour of Deformed Fiber,” ACI Materials Journal, Vol. 105, No. 6, 2008, pp. 576-584.
  8. Kim, D. J., El-Tawil, S., and Naaman, A. E., “Rate-Dependent Tensile Behaviour of High Performance Fiber Reinforced Cementitious Composites,” Materials and Structures, Vol. 42, No. 3, 2009, pp. 399-414. https://doi.org/10.1617/s11527-008-9390-x
  9. Kim, D. J., El-Tawil, S., and Naaman, A. E., “Correlation between Single Fiber Pullout Behaviour and Tensile Response of FRC Composites with High Strength Steel Fiber,” in Proceedings of Rilem International Workshop on High Performance Fiber Reinforced Cement Composites–HPFRCC5, Germany, H. W. Reinhardt and A.E. Naaman, Co-Editors, RILEM Proceedings, Pro. 53, S.A.R.L., Cachen, France, 2007, pp. 67-76.
  10. Naaman, A. E. and Sujivorakul, C., “Pull-out Mechanism of Twisted Steel Fibers Embedded in Concrete,” Proceedings of International Conference on Applications of Shotcrete, Tasmania, Austrailia, 2001, pp. 197-203.
  11. Sujivorakul, C., “Development of High Performance Fiber Reinforced Cementitious Composites Using Twisted Polygonal Steel Fibers,” Ph.D, Thesis, 2002, University of Michigan, Ann Arbor, 330 pp.
  12. Naaman, A. E., “Ferrocement & Laminated Cementitious Composites,” Techno Press 3000, Ann Arbor, Michigan, 2000, pp. 88-93.

Cited by

  1. Experimental Study on Tensile Strength of Steel Fiber-Reinforced Concrete Subjected to High Temperature vol.13, pp.1, 2013, https://doi.org/10.9798/KOSHAM.2013.13.1.063
  2. Tensile strength evaluation of SFRC subjected to high temperature using double punch test vol.15, pp.1, 2013, https://doi.org/10.9711/KTAJ.2013.15.1.001
  3. Enhancing the Performance of Polypropylene Fiber Reinforced Cementitious Composite Produced with High Volume Fly Ash vol.17, pp.3, 2013, https://doi.org/10.11112/jksmi.2013.17.3.118
  4. Bond Strength of Steel Fiber Incorporated in Ultra High Performance Fiber-Reinforced Concrete vol.25, pp.5, 2013, https://doi.org/10.4334/JKCI.2013.25.5.547