International journal of steel structures (국제강구조저널)

Korean Society of Steel Construction (한국강구조학회)
권호 표지
DOI QR코드

DOI QR Code

Nominal Moment Capacity of Hybrid Composite Sections using HSB600 High-Performance Steel

  • Youn, Seok-Goo (Department of Civil Engineering, Seoul National University of Science & Technology)
  • Published : 2013.06.30
⟨ Previous Next ⟩

Abstract

This paper contains a parametric study to develop provisions for predicting the nominal moment capacity of hybrid composite girders using HSB600 high-performance steel in the positive bending region. The ultimate moment capacity and the ductility of a wide range of hybrid composite sections are calculated using moment-curvature analysis, and the plastic moment of each section is obtained using simple plastic theory. The obtained moment capacity and the ductility of hybrid composite sections are compared to the previous research work and the current AASHTO LRFD's design equations. The comparison results show that there are considerable differences in moment capacity distribution between the hybrid composite sections and the conventional composite sections. It was also observed that the hybrid composite sections have sufficient rotation capacity similar to the conventional composite sections. Based on the results of the parametric study, new design equations are proposed for predicting the nominal moment capacity of hybrid composite sections. It is expected that the new design equations can be applied to simple supported or continuous hybrid composite beams in plastic design.

Keywords

References

  1. AASHTO (1994). LRFD bridge design specifications. 1st Ed., American Association of State Highway and Transportation Officails, Washington, D.C.
  2. AASHTO (2001). LRFD bridge design specifications. 2nd Ed., American Association of State Highway and Transportation Officails, Washington, D.C.
  3. AASHTO (2004). LRFD bridge design specifications. 3rd Ed., American Association of State Highway and Transportation Officails, Washington, D.C.
  4. AASHTO (2007). LRFD bridge design specifications, 4th Ed., American Association of State Highway and Transportation Officails, Washington, D.C.
  5. Ansourian, P. (1981). "Experiments on continuous composite beams." Proc. Institution of Civil Engineers, Part 2, Vol. 71, London, England, pp. 25-51.
  6. Ansourian, P. (1982). "Plastic rotation of composite beams." Journal of Structural Division, ASCE, 108(ST3), pp. 643-659.
  7. Barnard, P. (1965). "A series of tests on simply supported composite beams." Journal of the American Concrete Institute, 62(3), pp. 443-456.
  8. Barnard, P. R. and Johnson, R. P. (1965). "Plastic behaviour of continuous composite beams." Proc. Institution of Civil Engineers, Vol. 32, London, England, pp. 180-197.
  9. Barth, K. E. and Roberts, N. R. (2009). "Flexural capacity of compact composite I-girders in positive bending." Journal of Bridge Engineering, ASCE, 14(4), pp. 238-246. https://doi.org/10.1061/(ASCE)1084-0702(2009)14:4(238)
  10. Bitar, D., Trumpf, H., Galea, T., and Lukic, M. (2004). "Hybrid girders - strength and fatigue design rules based on experimental and numerical studies." Proc. 2004 Composite Construction in Steel and Concrete V, ASCE, South Africa, pp. 1-12.
  11. CEB (1990). CEB-FIP model code. Comite Euro-International du Beton, Thomas Telford, Laussance, Switzerland.
  12. ENV 1994-2 (2005). Eurocode 4 : Design of composite steel and concrete structures, Part 2. General rules and rules for bridges. European Committee for Standardization, Brussels.
  13. Gupta, V. K., Okui, Y., Inaba, N., and Nagai, M. (2007). "Effect of concrete crushing on flexural strength of steelconcrete composite girders." Journal of JSCE, A, 63(3), pp. 475-485.
  14. Lay, M. G. and Smith, P. D. (1965). "Role of strain hardening in plastic design." Journal of Structural Division, ASCE, 91(ST3), pp. 25-43.
  15. Lee, J. K., Yoon, T. Y., Choi, J. L., and Cho, J. Y. (2007). "Development and commercialization of high performance steel for bridges(HSB600)." Proc. Annual Conf. Korea Society of Steel Construction, KSSC, pp. 103-107 (in Korean).
  16. Mans, P., Yakel, A. J., and Azizinamini, A. (2001). "Fullscale testing of composite plaste girders constructed using 485-MPa high-performance steel." Journal of Bridge Engineering, ASCE, 6(6), pp. 598-604. https://doi.org/10.1061/(ASCE)1084-0702(2001)6:6(598)
  17. MOCT (2008). Design specifications for highway bridges. Ministry of Construction and Transportation, Korea (in Korean).
  18. Roberts, N. R. (2004). Evaluation of ductility of composite steel I-girders in positive bending. MS Thesis, West Virginia University, WV.
  19. Rotter, J. M. and Ansourian, P. (1979). "Cross-section behaviour and ductility in composite beams." Proc. Institution of Civil Engineers, Part 2, Vol. 67, London, England, pp. 453-474.
  20. Slutter, R. G. and Driscoll, G. C. (1965). "Flexural strength of steel-concrete composite beams." Journal of Structural Division, ASCE, 91(ST2), pp. 71-99.
  21. Wittry, D. M. (1993). An analysis study of the ductility of steel-concrete composite sections. MS Thesis, Univ. of Texas-Austin, Austin, TX.
  22. Yakel, A. J. and Azizinamini, A. (2005). "Improved moment strength prediction of composite steel plate girders in positive bending." Journal of Bridge Engineering, ASCE, 10(1), pp. 28-38. https://doi.org/10.1061/(ASCE)1084-0702(2005)10:1(28)
  23. Youn, S. G., Bae, D., and Kim, Y. J. (2008). "Ultimate flexural strength of hybrid composite girders using highperformance steel of HSB600 at sagging bending." Proc. 2008 Composite Construction in Steel and Concrete VI, ASCE, Colorado, pp. 680-690.

Cited by

  1. HSB 고성능 강재를 적용한 강합성 I-거더 정모멘트에 대한 휨저항강도 및 연성비 vol.26, pp.3, 2014, https://doi.org/10.7781/kjoss.2014.26.3.205
  2. Review of Design Flexural Strengths of Steel-Concrete Composite Beams for Building Structures vol.10, pp.3, 2013, https://doi.org/10.1007/s40069-016-0146-7
  3. Effect of Strain Hardening on the Flexural Resistance of Composite Plate Girders Using HSB600 High-Performance Steel in Positive Bending vol.22, pp.10, 2013, https://doi.org/10.1061/(asce)be.1943-5592.0001096
  4. HSB600 강재의 변형-경화를 고려한 강합성 I-거더의 정모멘트부 공칭휨강도 vol.29, pp.1, 2017, https://doi.org/10.7781/kjoss.2017.29.1.001