DOI QR코드

DOI QR Code

Spring-back Prediction of MS1470 Steel Sheets Based on a Non-linear Kinematic Hardening Model

이동경화 모델에 기반한 MS1470 강판의 스프링백 예측

  • Received : 2013.06.12
  • Accepted : 2013.09.03
  • Published : 2013.10.01

Abstract

Spring-back of MS1470 steel sheets was numerically predicted using a non-linear kinematic hardening material behavior based on the Yoshida-Uemori model. From uniaxial tension and uniaxial tension-compression-tension data as well as the uniaxial tension-unloading-tension data, the parameters of the Yoshida-Uemori model were obtained. For the numerical simulations, the Yoshida-Uemori model was implemented into the commercial finite element program, ABAQUS/Explicit and ABAQUS/Standard using the user-defined material subroutines. The model performance was validated against the measured spring-back from the benchmark problems of NUMISHEET 2008 and NUMISHEET 2011, the 2-D draw bending test and the S-rail forming test, respectively.

Keywords

References

  1. F. Yoshida, T. Uemori, 2002, A Model of Large-strain Cyclic Plasticity Describing the Bauschinger Effect and Workhardening Stagnation, Int. J. Plast., Vol. 18, No. 5-6, pp. 661-686. https://doi.org/10.1016/S0749-6419(01)00050-X
  2. T. Kuwabara, Y. Kumano, J. Ziegelheim, I. Kurosaki, 2009, Tension-compression Asymmetry of Phosphor Bronze for Electronic Parts and Its Effect on Bending Behavior, Int. J. Plast., Vol. 25, No. 9, pp. 1759-1776. https://doi.org/10.1016/j.ijplas.2009.01.004
  3. F. Yoshida, T. Uemori, 2003, A Model of Large-strain Cyclic Plasticity and its Application to Springback Simulation, Int. J. Mech. Sci., Vol. 45, No. 10, pp. 1687-1702. https://doi.org/10.1016/j.ijmecsci.2003.10.013
  4. K. Chung, T. Park, 2013, Consistency Condition of Isotropic-kinematic Hardening of Anisotropic Yield Functions with Full Isotropic Hardening under Monotonously Proportional Loading, Int. J. Plast., Vol. 45, pp. 61-84. https://doi.org/10.1016/j.ijplas.2012.10.012
  5. K. Chung, M.-G. Lee, D. Kim, C. M. Wenner, F. Barlat, 2005, Spring-back Evaluation of Automotive Sheets Based on Isotropic-kinematic Hardening Laws and Non-quadratic Anisotropic Yield Functions - Part I: Theory and Formulation, Int. J. Plast., Vol. 21, No. 5, pp. 861-882.
  6. K. Chung, T. Kuwabara, R. Verma, T. Park, 2011, BM4 - Pre-strain Effect on Spring-back of 2-D Draw Bending, in: H. Huh, K. Chung, S. S. Han, W. J. Chung,(Ed.), The NUMISHEET 2011 Benchmark Study of the 8th International Conference and Workshop on Numerical Simulation of 3D Sheet Metal Forming Processes, Korea, p. 175.
  7. K. Roll, K. Wiegand, P. Hora, 2008, Influence of Draw Beads on the Springback Behavior, in: P. Hora, W. Volk, K. Roll, B. Griesbach, L. Kessler, W. Hotz (Ed.), Proc. NUMISHEET2008, Part B Institute of Virtual Manufacturing, ETH, Zurich, pp. 45-111.

Cited by

  1. Spring-back Prediction of DP980 Steel Sheet Using a Yield Function with a Hardening Model vol.25, pp.3, 2016, https://doi.org/10.5228/KSTP.2016.25.3.189
  2. Application of Springback Analysis in the Development of a Reinforce Center Pillar Stamping Die vol.23, pp.5, 2014, https://doi.org/10.5228/KSTP.2014.23.5.297
  3. Process Design of Automobile Seat Rail Lower Parts using Ultra-High Strength, DP980 Steel vol.17, pp.2, 2018, https://doi.org/10.14775/ksmpe.2018.17.2.160