DOI QR코드

DOI QR Code

Simulation on the PCB Particle Trajectories in Corona-discharge Electrostatic Separator

코로나 방전 정전선별기 내 PCB 입자의 이동궤도 시뮬레이션

  • Han, Seongsoo (Department of Natural Resources and Environmental Engineering, Hanyang University) ;
  • Park, Seungsoo (Department of Natural Resources and Environmental Engineering, Hanyang University) ;
  • Kim, Seongmin (Department of Natural Resources and Environmental Engineering, Hanyang University) ;
  • Park, Jaikoo (Department of Natural Resources and Environmental Engineering, Hanyang University)
  • 한성수 (한양대학교 자원환경공학과) ;
  • 박승수 (한양대학교 자원환경공학과) ;
  • 김성민 (한양대학교 자원환경공학과) ;
  • 박재구 (한양대학교 자원환경공학과)
  • Received : 2014.09.30
  • Accepted : 2014.12.08
  • Published : 2014.12.31

Abstract

The trajectories of PCB(Printed Circuit Board) particles in the corona discharge electrostatic separation was simulated. The PCB particles are prepared by crushing bare board, which disassembled from electronic components, consist mostly of copper and FR-4(Flame Retardant Level-4) Firstly, a model was established for calculating of detachment points of PCB particles from the rotating electrode in separator. The model of detachment points was derived from equilibrium of force such as gravity force, centrifugal force, electrostatic force. The trajectories of particles after detachment was calculated by acceleration derived from time-integrating method of motion equation. In this simulation, particle size, supplied voltage, rotation speed of rotating roll electrode and angle of induction electrode were adopted as variables. While the trajectories of FR-4 particles were affected by all variables, rotation speed of rotating roll electrode was dominant variables affecting trajectories of copper particles.

코로나 방전 정전선별기 내에서 인쇄회로기판(Printed Circuit Board, PCB) 분쇄 입자의 이동궤도를 전산 모사하였다. 여기서 PCB입자는 전자부품 분리된 기판을 파쇄한 것으로, 대부분 구리와 FR-4(Flame Retardant Level-4)로 이루어져있다. 우선 입자가 선별기내 회전전극으로부터 탈착 지점을 계산하였으며, 중력, 원심력, 정전기력의 평형으로부터 유도되었다. 한편 탈착 후 이동궤도는 입자의 운동방정식으로부터 구한 가속도를 시간 적분하여 계산하였다. 시뮬레이션 변수는 입자의 크기, 공급전압의 세기, 회전전극속도 및 유도전극 각도로 하였다. 입자 이동궤도에 미치는 영향은 구리 입자의 경우에는 회전속도가 주요 변수였으나, 반면 FR-4 입자의 경우에는 상기 모든 변수에 영향을 받는 것으로 나타났다.

Keywords

References

  1. Cui Jirang, Forssberg Eric, 2003 : Mechanical recycling of waste electric and electronic equipment: a review, Journal of Hazardous Materials, 99(3), pp. 243-263. https://doi.org/10.1016/S0304-3894(03)00061-X
  2. Veit, H.M, Diehl, T.R., Salamia, A.P., Rodriguesa, J.S., Bernardesa, A.M., Tenoriob, J.A.S., 2005 : Utilization of magnetic and electrostatic separation in the recycling of printed circuit boards scrap, Waste Management, 25(1), pp. 67-74. https://doi.org/10.1016/j.wasman.2004.09.009
  3. Li Jia, Xu Zhenming, Zhou Yaohe, 2007 : Application of corona discharge and electrostatic force to separate metals and nonmetals from crushed particles of waste printed circuit boards, Journal of Electrostatics, 65, pp. 233-238. https://doi.org/10.1016/j.elstat.2006.08.004
  4. Menad, N., Bjorkman, B., Allain, E.G, 1998 : Combustion of plastics contained in electric and electronic scrap, Resources Conservation and Recycling, 24, pp. 65-85. https://doi.org/10.1016/S0921-3449(98)00040-8
  5. Iuga, A., Neamtu, V., Suarasan, I., Morar, R., Dascalesu, L., 1998 : Optimal high-voltage energization of coronaelectrostatic separators. IEEE Transaction on Industry Application, 34(2) pp. 286-293.
  6. Iuga, A., Dascalesu, L., Morar, R., Csorvassy, I., Neamtu, V., 1989 : Corona-electrostatic separators for recovery of waste non-ferrous metals, Journal of Electrostatics, 23, pp. 235-243. https://doi.org/10.1016/0304-3886(89)90051-X
  7. Wu Jiang, Li Jia, Xu Zhnming, 2009 : An improved model for computing the trajectories of conductive particles in roll-type electrostatic separator for recycling metals from WEEE, Journal of Hazardous Materials, 167, pp. 489-493. https://doi.org/10.1016/j.jhazmat.2009.01.005
  8. Tennal, K.B, Lindquist, D., Mazumer, M.K, Rajan, R., Guo W., Wu Jiang, 1999 : Efficiency of electrostatic separation of minerals from coal as function of size and charge distributions of coal particles, IEEE Transaction on Industry Application, 4, pp. 2137-2142.
  9. Li Jia, Lu Hongzhou, Liu Shushu, Xu Zhenming, 2008 : Optimizing the operating parameters of corona electrostatic separation for recycling waste scraped printed circuit boards by computer simulation of electric field, Journal of Hazardous Materials, 153, pp. 269-275. https://doi.org/10.1016/j.jhazmat.2007.08.047
  10. Amen, F., MorarJia, R., Kohnlechner, R., Samuila, A., Dascalescu, L., 2004 : High-Voltage Electrode Position : A Key Factor of Electrostatic Separation Efficiency, IEEE Transaction on Industry Application, 40(3) pp. 905-910.
  11. Dascalescu, L., Das, S., Kumar, U., 2009 : Numerical simulation of conductive particle behaviour at the surface of a plate electrode affected by a DC corona field, Journal of Electrostatic, 67, pp. 167-172. https://doi.org/10.1016/j.elstat.2008.11.010
  12. Lu Hongzhou, Li Jia, Jie Guo, Xu Zhenming, 2008 : Movement behavior in electrostatic separation : Recycling of metal materials from waste printed circuit board", Jounal of materials processing technology, 197, pp. 101-108. https://doi.org/10.1016/j.jmatprotec.2007.06.004
  13. Crowley, J.M., 1991 : Fundamentals of Applied Electrostatics, Krieger Publishing, Malabar, FL, pp. 19-20.
  14. Li Jia, Lu Hongzhou, Xu Zhenming, Zhou Yaohe, 2008 : A model for computing the trajectories of the conducting particles from waste printed circuit boards in corona electrostatic separators, Journal of Hazardous Materials, 151, pp. 52-57. https://doi.org/10.1016/j.jhazmat.2007.05.045
  15. Younes, M., Tilmatine, A., Medles, K., Rahli, M., Dascalescu, L., 2007 : Numerical of Conductive Particle Trajectories in Roll-Type Corona-Electrostatic Separators, IEEE Transaction on Industry Application, 43(5), pp. 1130-1136. https://doi.org/10.1109/TIA.2007.904363
  16. Younes, M., Tilmatine, A., Medles, K., Bendaoud, A., Samuila, A., Dascalescu, L., 2009 : Numerical Modeling of Insulating Particles Trajectories in Roll-type Corona-Electrostatic Separators, IEEE Transactions on Dielectrics and Electrical Insulation, 16(3), pp. 629-634. https://doi.org/10.1109/TDEI.2009.5128498
  17. Younes, A., Younes, M., Sayah, H., Bilici, M., Samuila, A., Dascalescu, L., 2013 : Effect of spark discharges on the trajectories of insulating particles in roll-type coronaelectrostatic separators. Experimental and numerical study, Journal of Electrostatics, 71, pp. 84-91. https://doi.org/10.1016/j.elstat.2012.10.003
  18. Li Jia, Xu Zhenming, Zhou Yaohe, 2008 : Theoretic model and computer simulation of separating mixture metal particles from waste printed circuit board by electrostatic separator, Journal of Hazardous Materials, 153, pp. 1308-1313. https://doi.org/10.1016/j.jhazmat.2007.09.089
  19. Wu Jiang, Li Jia, Jie Guo, Xu Zhenming, 2008 : Electrostatic separation for recovering metals and nonmetals from waste printed circuit board : problems and improvements, Environ. Sci. Technol., 42, pp. 5272-5276. https://doi.org/10.1021/es800868m
  20. Chao Guo, Hui Wang, Wei Liang, Jiangang Fu, Xin Yi, 2011 : Liberation characteristic and physical separation of printed circuit board(PCB), Waste management, 31, pp. 2161-2166. https://doi.org/10.1016/j.wasman.2011.05.011
  21. Li Jia, Lu Hongzhou, Xu Zhenming, Zhuo Yaohe, 2008 : Critical rotational speed model of the rotating roll electrode in corona electrostatic separation for recycling waste printed circuit boards, Journal of Hazardous Materials, 154, pp. 331-336. https://doi.org/10.1016/j.jhazmat.2007.10.030