Steel and Composite Structures

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Optimum distribution of steel slit-friction hybrid dampers based on life cycle cost

  • Eldin, Mohamed Nour (Department of Civil and Architectural Engineering, Sungkyunkwan University) ;
  • Kim, Jaegoo (Department of Civil and Architectural Engineering, Sungkyunkwan University) ;
  • Kim, Jinkoo (Department of Civil and Architectural Engineering, Sungkyunkwan University)
  • Received : 2017.12.29
  • Accepted : 2018.04.04
  • Published : 2018.06.10
⟨ Previous Next ⟩

Abstract

This study investigated the seismic performance of a hybrid damper composed of a steel slit plate and friction pads, and an optimum retrofit scheme was developed based on life cycle cost. A sample hybrid damper was tested under cyclic loading to confirm its validity as a damping device and to construct its nonlinear analysis model. The effectiveness of the optimum damper distribution schemes was investigated by comparing the seismic fragility and the life cycle costs of the model structure before and after the retrofit. The test results showed that the damper behaved stably throughout the loading history. Numerical analysis results showed that the slit-friction hybrid dampers optimally distributed based on life cycle cost proved to be effective in minimizing the failure probability and the repair cost after earthquakes.

Keywords

Acknowledgement

Supported by : National Research Foundation of Korea (NRF)

References

  1. AISC 341-10 (2010), Seismic Provisions for Structural Steel Buildings; American Institute of Steel Construction, Chicago, IL, USA.
  2. ASCE/SEI 41-13 (2013), American Society of Civil Engineers; Seismic Evaluation and Retrofit of Existing Buildings, Reston, VA, USA.
  3. ASCE/SEI 7-13 (2013), American Society of Civil Engineers; Minimum Design Loads for Buildings and Other Structures: Reston, VA, USA.
  4. Aslani, H. and Miranda, E. (2005), "Probability-based seismic response analysis", Eng. Struct., 27, 1151-1163. https://doi.org/10.1016/j.engstruct.2005.02.015
  5. Chan, R.W.K. and Albermani, F. (2008), "Experimental study of slit damper for passive energy dissipation", Eng. Struct., 30(4), 1058-1066. https://doi.org/10.1016/j.engstruct.2007.07.005
  6. Cornell, C.A., Jalayer, F., Hamburger, R.O. and Foutch, D.A. (2002), "Probabilistic basis for the 2000 SAC Federal Emergency Management Agency steel moment frame guidelines", J. Struct. Eng., 128(4), 526-533. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:4(526)
  7. Dolsek, M. (2012), "Simplified method for seismic risk assessment of buildings with consideration of aleatory and epistemic uncertainty", Struct. Infrastruct. Eng., 8(10), 939-953.
  8. Fan, X.W., Xu, L.H. and Li, Z.X. (2017), "Behaviors comparisons and prediction of pre-pressed spring self-centering energy dissipation braces", Int. J. Struct. Stabil. Dyn., 18(8), 1840006.
  9. FEMA (2012), Seismic Performance Assessment of Buildings: FEMA P-58, Prepared by the Applied Technology Council for the Federal Emergency Management Agency, Washington, D.C., USA.
  10. FEMA 461 (2007), Interim Testing Protocols for Determining the Seismic Performance Characteristics of Structural and Nonstructural Components; Applied Technology Council, Redwood City, CA, USA.
  11. Fragiadakis, M., Lagaros, N.D. and Papadrakakis, M. (2006), "Performance-based multi objective optimum design of steel structures considering life-cycle cost", Struct. Multidiscip. Optimiz., 32, 1-11. https://doi.org/10.1007/s00158-006-0009-y
  12. Gencturk, B. (2013), "Life-cycle cost assessment of RC and ECC frames using structural optimization", Earthq. Eng. Struct. Dyn., 42, 61-79. https://doi.org/10.1002/eqe.2193
  13. HAZUS-MH 2.1 (2010), Technical Manual; Federal Emergency Management Agency, Washington, D.C., USA.
  14. Hessabi, R.M. and Mercan, O. (2016), "Investigations of the application of gyro-mass dampers with various types of supplemental dampers for vibration control of building structures", Eng. Struct., 126, 174-186. https://doi.org/10.1016/j.engstruct.2016.07.045
  15. Hessabi, R.M., Mercan, O. and Ozturk, B. (2017), "Exploring the effects of tuned mass dampers on the seismic performance of structures with nonlinear base isolation systems", Earthq. Struct., Int. J., 12(3), 285-296. https://doi.org/10.12989/eas.2017.12.3.285
  16. International Construction Market Survey (2016), Turner & Townsend.
  17. Jeong, S. and Elnashai, A.S. (2007), "Probabilistic fragility analysis parameterized by fundamental response quantities", Eng. Struct., 29(6), 1238-1251. https://doi.org/10.1016/j.engstruct.2006.06.026
  18. Karunaratne, N., Thambiratnam, D.P. and Perera, N.J. (2016), "Magneto-rheological and passive damper combinations for seismic mitigation of building structures", Earthq. Struct., Int. J., 11(6), 1001-1025. https://doi.org/10.12989/eas.2016.11.6.1001
  19. Kim, J. and Jeong, J. (2016), "Seismic retrofit of asymmetric structures using steel plate slit dampers", J. Constr. Steel Res., 120, 232-244. https://doi.org/10.1016/j.jcsr.2016.02.001
  20. Kim, J. and Shin, H. (2017), "Seismic loss assessment of a structure retrofitted with slit-friction hybrid dampers", Eng. Struct., 130, 336-350. https://doi.org/10.1016/j.engstruct.2016.10.052
  21. Lee, J. and Kim, J. (2015), "Seismic performance evaluation of moment frames with slit-friction hybrid dampers", Earthq. Struct., Int. J., 9(6), 1291-1311. https://doi.org/10.12989/eas.2015.9.6.1291
  22. Lee, C.H., Lho, S.H., Kim, D.H., Oh, J. and Ju, Y.K. (2016), "Hourglass-shaped strip damper subjected to monotonic and cyclic loadings", Eng. Struct., 119(15), 122-134. https://doi.org/10.1016/j.engstruct.2016.04.019
  23. Lee, J., Kang, H. and Kim, J. (2017), "Seismic performance of steel plate slit-friction hybrid dampers", J. Constr. Steel Res., 136, 128-139. https://doi.org/10.1016/j.jcsr.2017.05.005
  24. Marko, J., Thambiratnam, D. and Perera, N. (2004), "Influence of damping systems on building structures subject to seismic effects", Eng. Struct., 26(13), 1939-1956. https://doi.org/10.1016/j.engstruct.2004.07.008
  25. Marshall, J.D. and Charney, F.A. (2012), "Seismic response of steel frame structures with hybrid passive control systems", Earthquake Engineering and Structural Dynamics, 41(4), 715-733. https://doi.org/10.1002/eqe.1153
  26. MATLAB (2012), The MathWorks, Inc.; Natick, MA, USA.
  27. Murakami, Y., Noshi, K., Fujita, K., Tsuji, M. and Takewaki, I. (2013), "Simultaneous optimal damper placement using oil, hysteretic and inertial mass dampers", Earthq. Struct., Int. J., 5(3), 261-276. https://doi.org/10.12989/eas.2013.5.3.261
  28. Nour Eldin, M. and Kim, J. (2017), "Simplified seismic life cycle cost estimation of a steel jacket offshore platform structure", Struct. Infrastruct. Eng., 13(8), 1027-1044. https://doi.org/10.1080/15732479.2016.1233286
  29. Park, J., Kim, J. and Min, K. (2004), "Optimal design of added viscoelastic dampers and supporting braces", Earthq. Eng. Struct. Dyn., 33, 465-484. https://doi.org/10.1002/eqe.359
  30. PEER (2006), PEER NGA Database; Pacific Earthquake Engineering Research Center, University of California, Berkeley, CA, USA. URL: http://peer.berkeley.edu/nga
  31. Perform 3D (2006), Computer and Structures Inc.; PERFORM User Guide ver 4.
  32. Pinto, P.E., Giannini, R. and Franchin, P. (2007), "Seismic Reliability Analysis of Structures", Earthq. Eng. & Struct. Dyn., 36(13), p. 2081. https://doi.org/10.1002/eqe.742
  33. RSMeans Building Construction Cost Data (2014), Waier, Phillip R. (EDT).
  34. Sun, B., Wang, M. and Gao, L. (2017), "Design principles for stiffness-tandem energy dissipation coupling beam", Smart Struct. Syst., Int. J., 20(1), 53-60.
  35. Tsai, C.S., Chen, K.‐C. and Chen, C.‐S. (1998), "Seismic Resistibility of High‐Rise Buildings with Combined Velocity‐Dependent and Velocity‐Independent Devices", Proceedings of ASME Pressure Vessels and Piping Conference, San Diego, CA, July, Volume 366, pp. 103-110.
  36. Uetani, K., Tsuji, M. and Takewaki, I. (2003), "Application of optimum design method to practical building frames with viscous dampers and hysteretic dampers", Eng. Struct., 25(5), 579-592. https://doi.org/10.1016/S0141-0296(02)00168-2
  37. Whittaker, A.S., Bertero, V.V., Thompson, C.L. and Alonso, L.J. (1991), "Seismic testing of steel-plate energy dissipating devices", Earthq. Spectra, 7(4), 563-604. https://doi.org/10.1193/1.1585644
  38. Xu, Z., Zhao, H. and Li, A. (2004), "Optimal analysis and experimental study on structures with viscoelastic dampers", J. Sound Vib., 273(3), 607-618. https://doi.org/10.1016/S0022-460X(03)00522-4
  39. Xu, Z., Tu, Q. and Guo, Y. (2012), "Experimental study on vertical performance of multi-dimensional earthquake isolation and mitigation devices for long-span reticulated structures", J. Vib. Control, 18(13), 1971-1985. https://doi.org/10.1177/1077546311429338
  40. Xu, Z., Xu, F. and Chen, X. (2016), "Study on intelligent vibration isolation and mitigation of the platform by using MR and VE devices", J. Aerosp. Eng., 29(4), 04016010. https://doi.org/10.1061/(ASCE)AS.1943-5525.0000604
  41. Xu, L.H., Fan, X.W. and Li, Z.X. (2017), "Cyclic behavior and failure mechanism of self-centering energy dissipation braces with pre-pressed combination disc springs", Earthq. Eng. Struct. Dyn., 46(7), 1065-1080. https://doi.org/10.1002/eqe.2844
  42. Zahrai, S.M., Moradi, A. and Moradi, M. (2015), "Using friction dampers in retrofitting a steel structure with masonry infill panels", Steel Compos. Struct., Int. J., 19(2), 309-325. https://doi.org/10.12989/scs.2015.19.2.309
  43. Zhan, M., Wang, S., Yang, T., Liu, Y. and Yu, B. (2017), "Optimum design and vibration control of a space structure with the hybrid semi-active control devices", Smart Struct. Syst., Int. J., 19(4), 341-350. https://doi.org/10.12989/sss.2017.19.4.341

Cited by

  1. Development of Seismic Retrofit Devices for Building Structures vol.8, pp.3, 2019, https://doi.org/10.21022/ijhrb.2019.8.3.221
  2. Steel hysteretic column dampers for seismic retrofit of soft-first-story structures vol.37, pp.3, 2018, https://doi.org/10.12989/scs.2020.37.3.259
  3. Seismic retrofit of structures using rotational friction dampers with restoring force vol.23, pp.16, 2018, https://doi.org/10.1177/1369433220939213
  4. Seismic retrofit of steel buildings using external resistant RC walls and friction dampers vol.76, pp.6, 2020, https://doi.org/10.12989/sem.2020.76.6.823
  5. Dynamic test and numerical simulation on avoiding the weak-story failure mechanism in structures using LSFDs vol.40, pp.2, 2021, https://doi.org/10.12989/scs.2021.40.2.175
  6. Evaluation of seismic performance of rotational-friction slip dampers in near-field and far-filed earthquakes vol.21, pp.2, 2018, https://doi.org/10.12989/eas.2021.21.2.147
  7. Improving the seismic performance of reinforced concrete frames using an innovative metallic-shear damper vol.28, pp.3, 2021, https://doi.org/10.12989/cac.2021.28.3.275