DOI QR코드

DOI QR Code

Experimental investigation on UHPC beams reinforced with GFRP and steel rebars and comparison with prediction equations

  • Parvin, Yousef Abbasi (Department of Civil Engineering, Tabriz Branch, Islamic Azad University) ;
  • Shaghaghi, Taleb Moradi (Department of Civil Engineering, Tabriz Branch, Islamic Azad University) ;
  • Pourbaba, Masoud (Department of Civil Engineering, Maragheh Branch, Islamic Azad University) ;
  • Mirrezaei, Seyyed Saeed (Department of Civil Engineering, Tabriz Branch, Islamic Azad University) ;
  • Zandi, Yousef (Department of Civil Engineering, Tabriz Branch, Islamic Azad University)
  • 투고 : 2021.09.03
  • 심사 : 2022.07.07
  • 발행 : 2022.07.25

초록

In this article, the flexural and shear capacity of ultra-high-performance fiber-reinforced concrete beams (UHPFRC) using two kinds of rebars, including GFRP and steel rebars, are experimentally investigated. For this purpose, six UHPFRC beams (250 × 300 × 1650 mm) with three reinforcement ratios (ρ) of 0.64, 1.05, and 1.45 were constructed using 2% steel fibers by volume. Half of the specimens were made of UHPFRC reinforced with GFRP rebars, while the other half were reinforced with conventional steel rebars. All specimens were tested to failure in four-point bending. Both the load-deformation at mid-span and the failure pattern were studied. The results showed that utilizing GFRP bars increases the flexural strength of UHPFRC beams in comparison to those made of steel bars, but at the same time, it reduces the post-cracking strain hardening. Furthermore, by increasing the percentage of longitudinal bars, both the post-cracking strain hardening and load-bearing capacity increase. Comparing the experiment results with some of the available equations and provisions cited in the valid design codes reveals that some of the equations to predict the flexural strength of UHPFRC beams reinforced with conventional steel and GFRP bars are reasonably conservative, while Khalil and Tayfur model is un-conservative. This issue makes it essential to modify the presented equations in this research for predicting the flexural strength of UHPFRC beams using GFRP bars.

키워드

참고문헌

  1. American Concrete Institute Committee 318 (2014), Building Code Requirements for Structural Concrete (ACI 318-14) and Commentary, Farmington Hills, MI, USA; American Concrete Institute.
  2. American Concrete Institute Committee 544 (1988), Design Considerations for Steel Fiber Reinforced Concrete, ACI 544.4R-88, Farmington Hills, MI, USA; American Concrete Institute.
  3. Adebar, P., Mindess, S., Pierre, D.S. and Olund, B. (1997), "Shear tests of fiber concrete beams without stirrups", Struct. J., 94(1), 68-76.
  4. Ahangarnazhad, B.H., Pourbaba, M. and Afkar, A. (2020), "Bond behavior between steel and Glass Fiber Reinforced Polymer (GFRP) bars and ultra high performance concrete reinforced by Multi-Walled Carbon Nanotube (MWCNT)", Steel Compos. Struct., Int. J., 35(4), 463-474. https://doi.org/10.12989/scs.2020.35.4.463
  5. Arslan, G., Keskin, R.S.O. and Ulusoy, S. (2017), "An experimental study on the shear strength of SFRC beams without stirrups", J. Theor. Appl. Mech., 55(4), 1205-1217. https://doi.org/10.15632/jtam-pl.55.4.1205
  6. Ashour, S.A., Hasanain, G.S. and Wafa, F.F. (1992), "Shear behavior of high-strength fiber reinforced concrete beams", Struct. J., 89(2), 176-184.
  7. ASTM Standard C150/C150M-15 (2015), Standard Specification for Portland Cement ASTM International, West Conshohocken, PA, USA. https://doi.org/10.1520/C0150-15 (www.astm.org)
  8. Baghaei Osgouei, Y., Tavousi Tafreshi, S. and Pourbaba, M. (2023), "Flexural Properties of UHPFRC Beams with an Initial Notch", J. Rehabil. Civil Eng., 11(1), 141-177. 10.22075/JRCE.2022.25513.1576
  9. Beshara, F., Shaaban, I. and Mustafa, T. (2012), "Nominal flexural strength of high strength fiber reinforced concrete beams", Arab. J. Sci. Eng., 37(2), 291-301. https://doi.org/10.1007/s13369-012-0172-y
  10. Campione, G. (2008), "Simplified flexural response of steel fiber-reinforced concrete beams", J. Mater. Civil Eng., 20(4), 283-293. https://doi.org/10.1061/(ASCE)0899-1561(2008)20:4(283)
  11. Canadian Standards Association (2012), Design and construction of building structures with fibre-reinforced polymers, Canadian Standards Association.
  12. Chellapandian, M., Mani, A. and Prakash, S.S. (2020), "Effect of macro-synthetic structural fibers on the flexural behavior of concrete beams reinforced with different ratios of GFRP bars", Compos. Struct., 254, 112790. https://doi.org/10.1016/j.compstruct.2020.112790
  13. Cosenza, E., Manfredi, G. and Realfonzo, R. (1997), "Behavior and modeling of bond of FRP rebars to concrete", J. Compos. Constr., 1(2), 40-51. https://doi.org/10.1061/(ASCE)1090-0268(1997)1:2(40)
  14. Dadmand, B., Pourbaba, M., Sadaghian, H. and Mirmiran, A. (2020a), "Effectiveness of steel fibers in ultra-high-performance fiber-reinforced concrete construction", Adv. Concrete Constr., Int. J., 10(3), 195-209. https://doi.org/10.12989/acc.2020.10.3.195
  15. Dadmand, B., Pourbaba, M., Sadaghian, H. and Mirmiran, A. (2020b), "Experimental & numerical investigation of mechanical properties in steel fiber-reinforced UHPC", Comput. Concrete, Int. J., 26(5), 451-465. https://doi.org/10.12989/cac.2020.26.5.451
  16. Dadmand, B., Pourbaba, M. and Riahi, R. (2022), "Experimental and Numerical Investigation of Different Types of Jacketing Effect on Retrofitting RC Short Columns Using ECC Concrete", Periodica Polytechnica Civil Eng., 66(2), 603-613. https://doi.org/10.3311/PPci.19114
  17. Dinh, H.H., Parra-Montesinos, G.J. and Wight, J.K. (2011), "Shear strength model for steel fiber reinforced concrete beams without stirrup reinforcement", J. Struct. Eng., 137(10), 1039-1051. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000362
  18. Ferrier, E., Michel, L., Zuber, B. and Chanvillard, G. (2015), "Mechanical behaviour of ultra-high-performance short-fibre-reinforced concrete beams with internal fibre reinforced polymer bars", Compos. Part B: Eng., 68, 246-258. https://doi.org/10.1016/j.compositesb.2014.08.001
  19. Goldston, M., Remennikov, A. and Sheikh, M.N. (2017), "Flexural behaviour of GFRP reinforced high strength and ultra high strength concrete beams", Constr. Build. Mater., 131, 606-617. https://doi.org/10.1016/j.conbuildmat.2016.11.094
  20. Graybeal, B.A. (2006), "Material property characterization of ultra-high performance concrete (No. FHWA-HRT-06-103)", Federal Highway Administration, Office of Infrastructure Research and Development.
  21. Graybeal, B. and Davis, M. (2008), "Cylinder or cube: strength testing of 80 to 200 MPa (11.6 to 29 ksi) ultra-high-performance fiber-reinforced concrete", ACI Mater. J., 105(6), 603.
  22. Hashim, D.T., Hejazi, F., Jaafar, M.S. and Lai, V.Y. (2019), "The Performance Evaluation of Circular Flange Bolted Connection in Ultra High Performance Fiber Reinforced Concrete Segmented Communication Tower", Periodica Polytechnica. Civil Engineering, 63(4), 971. https://doi.org/10.3311/PPci.12697
  23. Imam, M., Vandewalle, L. and Mortelmans, F. (1995), "Shear-moment analysis of reinforced high strength concrete beams containing steel fibres", Can. J. Civil Eng., 22(3), 462-470. https://doi.org/10.1139/l95-054
  24. Imam, M., Vandewalle, L., Mortelmans, F. and Van Gemert, D. (1997), "Shear domain of fibre-reinforced high-strength concrete beams", Eng. Struct., 19(9), 738-747. https://doi.org/10.1016/S0141-0296(96)00150-2
  25. Iranian National Building Regulations (2000), Design and construction of concrete structures, Ministry of Roads & Urban Development, Islamic Republic of Iran, Tehran, Iran.
  26. Kara, I.F. (2013), "Empirical modeling of shear strength of steel fiber reinforced concrete beams by gene expression programming", Neural Comput. Applicat., 23(3), 823-834. https://doi.org/10.1007/s00521-012-0999-x
  27. Khalil, W.I. and Tayfur, Y. (2013), "Flexural strength of fibrous ultra high performance reinforced concrete beams", ARPN J. Eng. Appl. Sci., 8(3), 200-214.
  28. Pourbaba, M. and Joghataie, A. (2019), "Determining shear capacity of ultra-high performance concrete beams by experiments and comparison with codes", Scientia Iranica, 26(1), 273-282. https://doi.org/10.24200/SCI.2017.4264
  29. Pourbaba, M., Asefi, E., Sadaghian, H. and Mirmiran, A. (2018a), "Effect of age on the compressive strength of ultra-high-performance fiber-reinforced concrete", Constr. Build. Mater., 175, 402-410. https://doi.org/10.1016/j.conbuildmat.2018.04.203
  30. Pourbaba, M., Joghataie, A. and Mirmiran, A. (2018b), "Shear behavior of ultra-high performance concrete", Constr. Build. Mater., 183, 554-564. https://doi.org/10.1016/j.conbuildmat.2018.06.117
  31. Pourbaba, M., Sadaghian, H. and Mirmiran, A. (2019a), "A comparative study of flexural and shear behavior of ultra-highperformance fiber-reinforced concrete beams", Adv. Struct. Eng., 22(7), 1727-1738. https://doi.org/10.1177/1369433218823848
  32. Pourbaba, M., Sadaghian, H. and Mirmiran, A. (2019b), "Flexural response of UHPFRC beams reinforced with steel rebars", Adv. Civil Eng. Mater., 8(3), 411-430.
  33. Sadaghian, H., Pourbaba, M., Andabili, S.Z. and Mirmiran, A. (2021), "Experimental and numerical study of flexural properties in UHPFRC beams with and without an initial notch", Constr. Build. Mater., 268, 121196. https://doi.org/10.1016/j.conbuildmat.2020.121196
  34. Swamy, R.N., Jones, R. and Chiam, A.T. (1993), "Influence of steel fibers on the shear resistance of lightweight concrete I-beams", Struct. J., 90(1), 103-114.
  35. Wille, K., El-Tawil, S. and Naaman, A.E. (2014), "Properties of strain hardening ultra high performance fiber reinforced concrete (UHP-FRC) under direct tensile loading", Cement Concrete Compos., 48, 53-66. https://doi.org/10.1016/j.cemconcomp.2013.12.015
  36. Xue, X., Hua, X. and Zhou, J. (2019), "Test and prediction of shear strength for the steel fiber-reinforced concrete beams", Adv. Mech. Eng., 11(4), 1687814019840551. https://doi.org/10.1177/1687814019840551
  37. Yang, J.-M., Min, K.-H., Shin, H.-O. and Yoon, Y.-S. (2012), "Effect of steel and synthetic fibers on flexural behavior of high-strength concrete beams reinforced with FRP bars", Compos. Part B: Eng., 43(3), 1077-1086. https://doi.org/10.1016/j.compositesb.2012.01.044
  38. Yoo, D.Y., Park, J.-J., Kim, S.-W. and Yoon, Y.-S. (2014), "Influence of reinforcing bar type on autogenous shrinkage stress and bond behavior of ultra high performance fiber reinforced concrete", Cement Concrete Compos., 48, 150-161. https://doi.org/10.1016/j.cemconcomp.2013.11.014
  39. Yoo, D.Y., Banthia, N. and Yoon, Y.-S. (2016a), "Flexural behavior of ultra-high-performance fiber-reinforced concrete beams reinforced with GFRP and steel rebars", Eng. Struct., 111, 246-262. https://doi.org/10.1016/j.engstruct.2015.12.003
  40. Yoo, D.-Y., Banthia, N. and Yoon, Y.-S. (2016b), "Predicting service deflection of ultra-high-performance fiber-reinforced concrete beams reinforced with GFRP bars", Compos. Part B: Eng., 99, 381-397. https://doi.org/10.1016/j.compositesb.2016.06.013